Welding Procedure Specifications

Welding Procedure Specification Example
Welding Procedure Specification Example
 

 A WPS is a document that describes how welding is to be carried out in production.  They are recommended for all welding operations and many application codes and standards make them mandatory

What information should they include?

 Sufficient details to enable any competent person to apply the information and produce a weld of acceptable quality.  The amount of detail and level of controls specified on a WPS is dependant on the application and criticality of the joint to be welded.

 For most applications the information required is generally similar to that recorded on a Procedure Qualification Record (PQR) or Welding Procedure Approval Record (WPAR), except that ranges are usually permitted on thicknesses, diameters, welding current, materials, joint types etc.

 If a WPS is used in conjunction with approved welding procedures then the ranges stated should be in accordance with the approval ranges permitted by the welding procedure.

 However careful consideration should be given to the ranges specified to ensure they are achievable, as the ranges given by welding procedure standards do not always represent good welding practice.  For example welding positions permitted by the welding procedure standard may not be achievable or practical for certain welding processes or consumables.

 EN ISO 15609-1 (formally EN 288 Part 2)  European Standard For Welding Procedure Specifications
EN ISO 15609 Defines the contents of a Welding Procedure Specification in the form of a list of information that should be recorded.  For some applications it may be necessary to supplement or reduce the list. For example only in the case of a procedure requiring heat input control would there be a necessity to quote travel speed or run-out length for manual processes.

 ASME IX  American Boiler and Pressure Vessel Code
QW 250 Lists the variables for each welding process, all the variables stated should be addressed.  The range permitted by the WPS is dictated by the PQR or PQRs used to qualify it. 


Typical Items That Should Be Recorded On W.P.S:-

     Common to all Processes        .

  • Procedure number
  • Process type
  • Consumable Size, Type and full Codification.
  • Consumable Baking Requirement if applicable
  • Parent material grade and spec.
  • Thickness range.
  • Plate or Pipe, Diameter range
  • Welding Position
  • Joint Fit Up, Preparation, Cleaning, Dimensions etc.
  • Backing Strip, Back Gouging information. 
  • Pre-Heat (Min Temp and Method)
  • Interpass If Required (Maximum Temperature recorded )
  • Post Weld Heat Treatment. If Required (Time and Temp)
  • Welding Technique (weaving,max run width etc.)
  • Arc Energy Limits should be stated if impact tests are required or if the material being welded is sensitive to heat input.
Specific To Welding Processes MMA TIG MIG
MAG
FCAW
SUB
ARC
Welding current  yes yes yes yes
Type of Welding current AC/DC   Polarity  yes yes yes yes
Arc voltage   If Auto yes yes
Pulse parameters (Pulse time and peak & backgound current)    If Used If Used  
Welding Speed If Mechanised   yes yes yes
Wire configuration        yes
Shielding gas (comp,flow rate)    yes yes  
Purge gas (comp & flow rate)    If Used If Used  
Tungsten electode Diameter and type.    yes    
Nozzle diameter    yes yes  
Type of Flux Codification & Brand Name        yes
Nozzle Stand Off Distance (Distance from tip of nozzle to workpiece).       yes

Sketches
A sketch of the joint configuration is required which should include the basic dimensions of the weld preparation.  Some indication of the run sequence is also beneficial, particularly if the correct sequence is essential to ensure the properties of the weld are maintained. 

Production Sequence
Whilst this is good practice it is not a requirement of either ASME 9 or EN288 Part 2; it could be issued as a separate QA procedure if preferred.

Non Destructive Testing
A WPS is primarily concerned with welding not N D T, this activity should be covered by separate N D T procedures.

 

Page last updated 21 March2008